The Aviation Science

Helicopter Flight Control System 🛩️helicopter pilot manipulates the helicopter flight controls to achieve and maintain controlled aerodynamic flight. 🛩️Changes to the helicopter flight control system transmit mechanically to the rotor, producing aerodynamic effects on the rotor blades that make the helicopter move in a deliberate way. 🛩️To tilt forward and back (pitch) or sideways (roll), requires that the controls alter the angle of attack of the main rotor blades cyclically during rotation, creating differing amounts of lift(forces) at different points in the cycle. 🛩️To increase or decrease overall lift requires that the controls alter the AoA for all blades collectively by equal amounts at the same time, resulting in ascent, descent, acceleration and deceleration. 🛩️A typical helicopter has three flight control inputs—the cyclic stick, the collective lever, and the anti-torque pedals. 🛩️Depending on the complexity of the helicop...

Five Major Stresses 🛩️Aircraft structural members are designed to carry a load or to resist stress. Aircraft parts must be planned to carry the load to be imposed upon it. 🛩️The term stress is often used interchangeably with the word “strain.” They are not the same thing. External loads or forces cause stress. Stress is a material’s internal resistance, or counterforce, that opposes deformation. The degree of deformation of a material is strain. When a material is subjected to a load or force, that material is deformed, regardless of how strong the material is or how light the load is. 🛩️Here 5 major stresses to which aircraft is subjected ✳️Tension ✳️Compression ✳️Torsion ✳️Shear ✳️Bending ✈️Tension is the stress that resists a force that tends to pull something apart. The engine pulls the aircraft forward, but air resistance tries to hold it back. The result is tension, which stretches the aircraft. The tensile strength of a material is measured in pounds per square inc...

Hydraulic System 🛩️There are multiple applications for hydraulic use in aircraft depending on the complexity of the aircraft. For example, a hydraulic system is often used on small airplanes to operate wheel brakes, retractable landing gear, and some constant speed propellers. 🛩️On large airplanes, a hydraulic system is used for flight control surfaces, wing flaps, spoilers, and other systems. 🛩️A basic hydraulic system consists of a reservoir, pump (either hand, electric or engine-driven), a filter to keep the fluid clean, a selector valve to control the direction of flow, a relief valve to relieve excess pressure, and an actuator. 🛩️The hydraulic fluid is pumped through the system to an actuator or servo. A servo is a cylinder with a piston inside that turns fluid power into work and creates the power needed to move an aircraft system or flight control. Servos can be either single-acting or double-acting, based on the needs of the system. This means that the fluid can be...

Lateral and Longitudinal Balance 🛩️Balance refers to the location of the CG of an aircraft, and is important to stability and safety in flight. The CG is a point at which the aircraft would balance if it were suspended at that point. 🛩️The primary concern in balancing an aircraft is the fore and aft location of the CG along the longitudinal axis. The CG is not necessarily a fixed point; its location depends on the distribution of weight in the aircraft. 🛩️As variable load items are shifted or expended, there is a resultant shift in CG location. The distance between the forward and back limits for the position of the center for gravity or CG range is certified for an aircraft by the manufacturer. 🛩️The pilot should realize that if the CG is displaced too far forward on the longitudinal axis, a nose-heavy condition will result. Conversely, if the CG is displaced too far aft on the longitudinal axis, a tail heavy condition results. It is possible that the pilot could not c...

Forces in Turn 🛩️If an aircraft were viewed in straight & level flight from the front & if the forces acting on the aircraft could be seen, lift & weight would be apparent: two forces.If the aircraft were in a bank it would be apparent that lift did not act directly opposite to the weight, rather it now acts in the direction of the bank. When the aircraft banks, lift acts inward toward the center of the turn, perpendicular to the lateral axis as well as upward. 🛩️An increase in airspeed results in an increase of the turn radius, & centrifugal force is directly proportional to the radius of the turn. In a correctly executed turn, the horizontal component of lift must be exactly equal & opposite to the centrifugal force. As the airspeed is increased in a constant-rate level turn, the radius of the turn increases. This increase in the radius of turn causes an increase in the centrifugal force, which must be balanced by an increase in the horizontal compo...

Airport Markings ➡️Subscribe us for more aircraft knowledge and aircraft fact⬅️ ➡️Do Share with your Friends⬅️

Vortex Devices 🛩️Vortex devices maintain airflow at low speeds and delay the stall, by creating a vortex which re-energises the boundary layer close to the wing . 🛩️Vortex generator: small triangular protrusion on the upper leading wing surface; usually, several are spaced along the span of the wing. Vortex generators create additional drag at all speeds . 🛩️Vortilon: a flat plate attached to the underside of the wing near its outer leading edge, roughly parallel to normal airflow. At low speeds, tip effects cause a local spanwise flow which is deflected by the vortilon to form a vortex passing up and over the wing . 🛩️Leading-edge root extension (LERX): generates a strong vortex over the wing at high angles of attack, but unlike vortex generators it can also increase lift at such high angles, while creating minimal drag in level flight. ➡️Subscribe us for more aircraft knowledge and aircraft fact⬅️ ➡️Do Share with your Friends⬅️

Drag Reduction Devices 🛩️Anti-shock body: a streamlined pod shape added to the leading or trailing edge of an aerodynamic surface, to delay the onset of shock stall and reduce transonic wave drag. Sometimes called a Küchemann carrot . 🛩️Fillet: a small curved infill at the junction of two surfaces, such as a wing and fuselage, blending them smoothly together to reduce drag . 🛩️Fairings of various kinds, such as blisters, pylons and wingtip pods, containing equipment which cannot fit inside the wing, and whose only aerodynamic purpose is to reduce the drag created by the equipment ➡️Subscribe us for more aircraft knowledge and aircraft fact⬅️ ➡️Do Share with your Friends⬅️

High Lifting Devices 🛩️The most common types of High-lift devices are fixed slots, movable slats, leading edge flaps, and cuffs. 🛩️Fixed slots direct airflow to the upper wing surface and delay airflow separation at higher angles of attack. 🛩️The slot does not increase the wing camber, but allows a higher maximum CL because the stall is delayed until the wing reaches a greater AoA. 🛩️Movable slats consist of leading edge segments that move on tracks, At low AoA, each slat is held flush against the wing’s leading edge by the high pressure that forms at the wing’s leading edge. 🛩️As the AoA increases, the high pressure area moves aft below the lower surface of the wing, allowing the slats to move forward. 🛩️Some slats, however, are pilot operated and can be deployed at any AoA. Opening a slat allows the air below the wing to flow over the wing’s upper surface, delaying airflow separation. 🛩️Leading edge flaps and Leading edge cuffs , like trailing edge flaps, are ...