𝐄𝐦𝐩𝐞𝐧𝐧𝐚𝐠𝐞

Empennage

🛩️The empennage of an aircraft is also known as the tail section. Most empennage designs consist of a tail cone, fixed aerodynamic surfaces or stabilizers, and movable aerodynamic surfaces.

🛩️The tail cone serves to close and streamline the aft end of most fuselages. The cone is made up of structural members like those of the fuselage; however, cones are usually of lighter construction since they receive less stress than the fuselage.

🛩️The other components of the typical empennage are of heavier construction than the tail cone. These members include fixed surfaces that help stabilize the aircraft and movable surfaces that help to direct an aircraft during flight. The fixed surfaces are the horizontal stabilizer and vertical stabilizer. The movable surfaces are usually a rudder located at the aft edge of the vertical stabilizer and an elevator located at the aft edge the horizontal stabilizer.

🛩️The structure of the stabilizers is very similar to that which is used in wing construction. Figure shows a typical vertical stabilizer. The use of spars, ribs, stringers, and skin like those found in a wing are also used here. They perform the same functions shaping and supporting the stabilizer and transferring stresses.

🛩️Bending, torsion, and shear created by air loads in flight pass from one structural member to another. Each member absorbs some of the stress and passes the remainder on to the others. Ultimately, the spar transmits any overloads to the fuselage. A horizontal stabilizer is built the same way.

➡️Subscribe us for more aircraft knowledge and aircraft fact⬅️
➡️Do Share with your Friends⬅️

Comments

𝐖𝐞𝐭-𝐒𝐮𝐦𝐩 𝐎𝐢𝐥 𝐒𝐲𝐬𝐭𝐞𝐦

Wet Sump Oil System ✳️The engine oil system performs several important functions: 🛩️Lubrication of the engine’s moving parts . 🛩️Cooling of the engine by reducing friction . 🛩️Removing heat from the cylinders . 🛩️Carrying away contaminants . 🛩️Providing a seal between the cylinder walls and pistons. ➡️Subscribe us for more aircraft knowledge and aircraft fact⬅️ ➡️Do Share with your Friends⬅️

𝐓𝐲𝐩𝐞𝐬 𝐨𝐟 𝐂𝐨𝐦𝐛𝐮𝐬𝐭𝐢𝐨𝐧 𝐂𝐡𝐚𝐦𝐛𝐞𝐫𝐬

🛩️A combustor is a component or area of a gas turbine, ramjet, or scramjet engine where combustion takes place. It is also known as a burner, combustion chamber or flame holder. In a gas turbine engine, combustion chamber is fed high pressure air by the compression system. 🛩️The combustor then heats this air at constant pressure. After heating, air passes from the combustor through the nozzle guide vanes to the turbine. In the case of a ramjet or scramjet engines, the air is directly fed to the nozzle. 𝐀𝐧𝐧𝐮𝐥𝐚𝐫 𝐓𝐲𝐩𝐞 ✈️The most commonly used type of combustor is the fully annular combustor. Annular combustors do away with the separate combustion zones and simply have a continuous liner and casing in a ring. There are many advantages to annular combustors, including more uniform combustion, shorter size, lighter, and less surface area. Annular combustors tend to have very uniform exit temperatures. They also have the lowest pressure drop of the three...

𝐂𝐥𝐨𝐮𝐝𝐬

Basic Clouds 🛩️Cloud type is determined by its height, shape, & characteristics. They are classified according to the height of their bases as low, middle, or high clouds, as well as clouds with vertical development. 🛩️Low clouds are those that form near the Earth’s surface and extend up to about 6,500 feet AGL. They are made of water droplets but can include supercooled water droplets that induce hazardous aircraft icing. Typical low clouds are stratus, stratocumulus, nimbostratus. Fog is also low cloud formation. This Clouds create low ceilings, hamper visibility, & can change rapidly. They influence flight planning & can make visual flight rules (VFR) flight impossible. 🛩️Middle clouds form around 6,500 feet AGL & extend up to 20,000 feet AGL. They are composed of water, ice crystals, & supercooled water droplets. Typical middle-level clouds include altostratus & altocumulus. These types of clouds are encountered on cross-country flights at highe...

The Aviation Science

Search This Blog